How to empty Dyson vacuum V10? – The Dyson vacuum D10 is robust and simple to operate. Emptying the debris bin is one of the most crucial things you can do to maintain your cordless vacuum. We have done our homework and gathered information on how to take a few cordless Dysons’ trash baskets out.
Table of Contents
How to empty Dyson vacuum V10 cordless
Dyson V10 and V11 cordless sticks vacuums share a similar construction. The V11 has the stronger suction of the two. The stick attachment will need to be removed before emptying the debris canister.
There will be a red button where the stick attachment and the debris canister meet. Press the button while pulling the stick off to remove it. There will be a red lever on the back of the canister to empty the debris. Hold the vacuum over a garbage bin and push down the red lever to empty the canister.
How to empty Dyson vacuum V10 in detail
Step 1: In order to open or release the cap of the canister, you must first detach the wand from it. To do this, locate the red button on the wand on the end that is attached to the dust cup; push it down to release the wand and set it aside.
Step 2: Hold the cylinder over a dustbin or tray (to catch the debris) and point it downward; grab hold of the lever on the bin which should be facing you while the device is held in this position. Push it down firmly and, in one fluid movement, the canister will get released and be pushed down while the cap simultaneously opens up. This will allow the dust cup to empty out.
Step 3: As the debris empties out of your Dyson Cyclone v10 bin, you might find some dust, hair, and other debris stuck inside or clinging to the sides of the canister; this can easily be cleaned out with a damp cloth or a narrow cleaning brush if your hand does not reach all the way in. If you are using a damp cleaning tool, be sure to let the interior of the bin dry completely before closing it back up.
Step 4: Once you have emptied and cleaned the dust cup thoroughly, close the cap and push the canister back down (it should click back into place). Just like releasing or opening the dust cup, pushing it back up should be done in one, clean motion. If the canister isn’t moving smoothly, check for any trapped debris at the bottom of the cup. Use an old toothbrush or dust cloth to clean this area before closing the canister again.
How to Remove & Clean Dyson v10 Filter
The filter of your vacuum cleaner bears large amounts of dust and debris over time and therefore, is prone to clogging. This significantly reduces the suction power and can also disrupt the normal functioning of the appliance. As we mentioned earlier, the Dyson v10 Cyclone Vacuum Cleaner will display a warning light to indicate a clog; this is typically situated in the filter.
While it is advisable to check the filter routinely and give it a quick clean, if you have waited too long and the warning light starts flashing, turn off the appliance immediately and clean the filter using the steps below:
- Locate the filter on the back of the handle, twist it counter-clockwise, and pull it out.
- Use a clean micro-fibre cloth to wipe around the area where the filter sits on the unit. You can also use a small brush to do this.
- To clean the filter, rinse it thoroughly under cool running water. Be sure to wash off all the dust and debris.
- If needed, use a soft brush to remove dirt that is clinging to the filter mesh.
- Turn the filter upside down and leave it to dry on a rack.
WARNING: Do not put the filter back in until it is completely dry as any dampness can damage the electricals inside.
How to remove the bin of Dyson Cyclone V10
Remove the clear bin
- Fully push the red bin release lever away from the handle of the machine.
- Press and hold the red catch on the underside of the bin and slide the bin off the machine.
Check bin seals
- Check the seals around the top of the bin where it fits to the machine and check the seals around the rim of the bin lid for any damage.
Check the cyclone shroud and inlet
- Make sure there isn’t a buildup of dust and debris around the cyclone shroud after removing the bin. As necessary, remove.
- There is a little entrance on the right side of the cyclone, with the machine facing away from you.
- If required, remove any dust, debris, or fibers from the inlet.
- Re-assemble and test the machine.
Things to remember when using Dyson Cyclone V10
Additionally, it should be noted that the vacuum cleaner filter may become worn out or broken over time and will need to be changed with a new one to maintain the appliance’s overall effectiveness. You can buy a new Dyson v10 filter directly from the manufacturer; only buy genuine filters as knockoffs are frequently constructed with subpar materials.
Wrap up
The article of How to empty Dyson vacuum V10 of Best Vacuum Cleaning is going to end here. Thank you for reading and hope this help you in maintaining your Dyson vacuum effectively. See you again in the next tips for maintenance.
